Port 4088 NPSP
Port 4088 is the IANA-assigned npsp port for Noah Printing Service Protocol (TCP).
What is port 4088 used for?
Port 4088 is assigned to npsp and uses TCP. The IANA registry describes the service as “Noah Printing Service Protocol”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach npsp connects to port 4088. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 4088 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Hiromi_Ohara].
Check and block port 4088
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :4088'Check on Windows
Get-NetTCPConnection -LocalPort 4088 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 4088/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 4088 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 4088 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 4088 is usually used
Most traffic on port 4088 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Print clients submitting jobs to a shared printer or print server.
- Print servers advertising queues to workstations on the LAN.
- Troubleshooting jobs stuck in the spooler or a blocked driver port.
Check the printer port
A TCP probe tells you whether the device is reachable; driver-level errors come later.
nc -vz 192.168.1.50 4088Common problems with port 4088
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 4088. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :4088' or sudo lsof -i :4088. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 4088 at a glance
| Port number | 4088 |
|---|---|
| Service name | npsp |
| Transport protocol | TCP |
| Category | Printing |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Hiromi_Ohara] |
| Registry description | Noah Printing Service Protocol |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 4088 used for?
Port 4088 (NPSP) uses TCP. Noah Printing Service Protocol.
How do I check if port 4088 is open?
On Linux run `sudo ss -tlpn 'sport = :4088'`. On Windows run `Get-NetTCPConnection -LocalPort 4088 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 4088; empty output usually means nothing is bound to it.
How do I block port 4088?
With UFW run `sudo ufw deny 4088/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 4088 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 4088 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 4086 · ftsyncFirewall/NAT state table synchronization
- Port 4089 · opencoreOpenCORE Remote Control Service
- Port 3396 · printer-agentPrinter Agent IANA assigned this well-formed service name as a…
- Port 4391 · apwi-imserverAmerican Printware IMServer Protocol
- Port 2291 · eapspEPSON Advanced Printer Share Protocol
- Port 4392 · apwi-rxserverAmerican Printware RXServer Protocol
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy