Port 7545 NTA-US
Port 7545 is the IANA-assigned nta-us port for FlowAnalyzer UtilityServer (TCP / UDP).
What is port 7545 used for?
Port 7545 is assigned to nta-us and uses TCP / UDP. The IANA registry describes the service as “FlowAnalyzer UtilityServer”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach nta-us connects to port 7545. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 7545 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Fred_Messinger].
Check and block port 7545
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :7545'
sudo ss -ulpn 'sport = :7545'Check on Windows
Get-NetTCPConnection -LocalPort 7545 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 7545 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 7545/tcp
sudo ufw deny 7545/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 7545 -j DROP
sudo iptables -A INPUT -p udp --dport 7545 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 7545 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 7545 is usually used
Most traffic on port 7545 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Application backends and supporting services that use a fixed registered number.
- Containers or local stacks that publish the port on the host.
- Firewall and exposure reviews before the service goes to production.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 7545Common problems with port 7545
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 7545. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :7545' or sudo lsof -i :7545. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 7545 at a glance
| Port number | 7545 |
|---|---|
| Service name | nta-us |
| Transport protocol | TCP / UDP |
| Category | Application services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Fred_Messinger] |
| Registry description | FlowAnalyzer UtilityServer |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 7545 used for?
Port 7545 (NTA-US) uses TCP / UDP. FlowAnalyzer UtilityServer.
How do I check if port 7545 is open?
On Linux run `sudo ss -tlpn 'sport = :7545'` and `sudo ss -ulpn 'sport = :7545'`. On Windows run `Get-NetTCPConnection -LocalPort 7545 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 7545 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 7545; empty output usually means nothing is bound to it.
How do I block port 7545?
With UFW run `sudo ufw deny 7545/tcp` and `sudo ufw deny 7545/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 7545 -j DROP` and `sudo iptables -A INPUT -p udp --dport 7545 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 7545 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 7544 · nta-dsFlowAnalyzer DisplayServer
- Port 7548 · tidpThreat Information Distribution Protocol
- Port 7542 · saratogaSaratoga Transfer Protocol
- Port 7549 · nls-tlNetwork Layer Signaling Transport Layer
- Port 7510 · ovhpasHP OpenView Application Server
- Port 7551 · controlone-conControlONE Console signaling
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy