Port 5635 SFMSSO
Port 5635 is the IANA-assigned sfmsso port for SFM Authentication Subsystem (TCP).
What is port 5635 used for?
Port 5635 is assigned to sfmsso and uses TCP. The IANA registry describes the service as “SFM Authentication Subsystem”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach sfmsso connects to port 5635. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5635 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all Authentication and access ports
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [De_Chih_Chien].
Check and block port 5635
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5635'Check on Windows
Get-NetTCPConnection -LocalPort 5635 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5635/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5635 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 5635 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 5635 is usually used
Most traffic on port 5635 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Network devices authenticating users through a central service.
- Wi-Fi, VPN and remote-access gateways enforcing access policy.
- Accounting and session logs used for audits.
Probe the auth service
Authentication protocols are sensitive to shared secrets and source addresses, so test from an authorised client.
nc -vz 127.0.0.1 5635Common problems with port 5635
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5635. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5635' or sudo lsof -i :5635. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5635 at a glance
| Port number | 5635 |
|---|---|
| Service name | sfmsso |
| Transport protocol | TCP |
| Category | Authentication and access |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [De_Chih_Chien] |
| Registry description | SFM Authentication Subsystem |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5635 used for?
Port 5635 (SFMSSO) uses TCP. SFM Authentication Subsystem.
How do I check if port 5635 is open?
On Linux run `sudo ss -tlpn 'sport = :5635'`. On Windows run `Get-NetTCPConnection -LocalPort 5635 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5635; empty output usually means nothing is bound to it.
How do I block port 5635?
With UFW run `sudo ufw deny 5635/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5635 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 5635 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 5633 · beorlBE Operations Request Listener
- Port 5638 · flcrsSymantec Fingerprint Lookup and Container Reference Service
- Port 4129 · nuauthNuFW authentication protocol
- Port 7004 · afs3-kaserverAFS/Kerberos authentication service
- Port 3799 · radius-dynauthRADIUS Dynamic Authorization
- Port 7847 · csoauthA product key authentication protocol made by CSO
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy