Port 5543 QFTEST-LIC-MCP
Port 5543 is the IANA-assigned qftest-lic-mcp port for QF-Test License Server / QF-Test MCP Server (TCP).
What is port 5543 used for?
Port 5543 is assigned to qftest-lic-mcp and uses TCP. The IANA registry describes the service as “QF-Test License Server / QF-Test MCP Server”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach qftest-lic-mcp connects to port 5543. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5543 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Quality_First_Software_GmbH].
Check and block port 5543
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5543'Check on Windows
Get-NetTCPConnection -LocalPort 5543 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5543/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5543 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 5543 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 5543 is usually used
Most traffic on port 5543 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Application backends and supporting services that use a fixed registered number.
- Containers or local stacks that publish the port on the host.
- Firewall and exposure reviews before the service goes to production.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 5543Common problems with port 5543
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5543. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5543' or sudo lsof -i :5543. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5543 at a glance
| Port number | 5543 |
|---|---|
| Service name | qftest-lic-mcp |
| Transport protocol | TCP |
| Category | Application services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Quality_First_Software_GmbH] |
| Registry description | QF-Test License Server / QF-Test MCP Server |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5543 used for?
Port 5543 (QFTEST-LIC-MCP) uses TCP. QF-Test License Server / QF-Test MCP Server.
How do I check if port 5543 is open?
On Linux run `sudo ss -tlpn 'sport = :5543'`. On Windows run `Get-NetTCPConnection -LocalPort 5543 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5543; empty output usually means nothing is bound to it.
How do I block port 5543?
With UFW run `sudo ufw deny 5543/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5543 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 5543 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 5540 · matterMatter Operational Discovery and Communi
- Port 5550 · cbusModel Railway control using the CBUS message protocol
- Port 5507 · psl-managementPowerSysLab Electrical Management
- Port 5567 · dof-dps-mc-secDOF Protocol Stack Multicast/Secure Transport
- Port 5475 · apsolab-dataThe Apsolab company's data retrieval protocol
- Port 5568 · sdtSession Data Transport Multicast
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy