Port 5233 ENFS
Port 5233 is the IANA-assigned enfs port for Etinnae Network File Service (TCP).
What is port 5233 used for?
Port 5233 is assigned to enfs and uses TCP. The IANA registry describes the service as “Etinnae Network File Service”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach enfs connects to port 5233. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5233 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all File transfer and sharing ports
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Chris_Peel].
Check and block port 5233
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5233'Check on Windows
Get-NetTCPConnection -LocalPort 5233 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5233/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5233 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 5233 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 5233 is usually used
Most traffic on port 5233 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Transferring build artifacts, backups or exports between trusted hosts.
- Mounting or browsing shared directories inside a private network.
- Scheduled sync jobs that connect on a fixed port.
Check the service
Probe the port before debugging credentials or share permissions.
nc -vz 127.0.0.1 5233Common problems with port 5233
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5233. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5233' or sudo lsof -i :5233. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5233 at a glance
| Port number | 5233 |
|---|---|
| Service name | enfs |
| Transport protocol | TCP |
| Category | File transfer and sharing |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Chris_Peel] |
| Registry description | Etinnae Network File Service |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5233 used for?
Port 5233 (ENFS) uses TCP. Etinnae Network File Service.
How do I check if port 5233 is open?
On Linux run `sudo ss -tlpn 'sport = :5233'`. On Windows run `Get-NetTCPConnection -LocalPort 5233 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5233; empty output usually means nothing is bound to it.
How do I block port 5233?
With UFW run `sudo ufw deny 5233/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5233 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 5233 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 5232 · csedaemonCruse Scanning System Service
- Port 5243 · xycstatusxyClient Status API and rendevous point
- Port 2257 · simple-tx-rxsimple text/file transfer
- Port 7117 · rothagaEncrypted chat and file transfer service
- Port 2175 · airsyncMicrosoft Desktop AirSync Protocol
- Port 20048 · mountdNFS mount protocol
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy