Port 5060 SIP
Port 5060 is the IANA-assigned sip port for SIP (TCP / UDP / SCTP).
What is port 5060 used for?
Port 5060 is assigned to sip and uses TCP / UDP / SCTP. The IANA registry describes the service as “SIP”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach sip connects to port 5060. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5060 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all Voice and real-time media ports
Source: IANA Service Name and Transport Protocol Port Number Registry. Reference: [RFC 3263].
Check and block port 5060
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5060'
sudo ss -ulpn 'sport = :5060'
sudo ss -Slpn 'sport = :5060'Check on Windows
Get-NetTCPConnection -LocalPort 5060 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 5060 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5060/tcp
sudo ufw deny 5060/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5060 -j DROP
sudo iptables -A INPUT -p udp --dport 5060 -j DROP
sudo iptables -A INPUT -p sctp --dport 5060 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled. UFW and the built-in Windows cmdlets cover TCP and UDP only; this port also lists SCTP, so use nftables, iptables or the vendor's diagnostic tool for those protocols. SCTP and DCCP handling also depends on kernel support, including their diagnostic modules, so a missing result may mean the module is not loaded rather than that nothing is listening.
Is port 5060 safe to expose?
SIP endpoints are scanned for toll fraud and registration hijacking. Require authentication, rate limiting and a trusted SIP trunk. Expose this port only when the service is actually needed. Keep it patched, prefer an encrypted alternative, and limit source addresses with a firewall allowlist.
Where port 5060 is usually used
Most traffic on port 5060 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- VoIP call setup and media streams between clients and a PBX.
- Conference, contact-centre or SIP-trunk infrastructure.
- Firewall reviews for real-time traffic that is sensitive to latency.
Probe the signalling port
SIP and media traffic may use TCP or UDP depending on the provider, so confirm the transport before you test.
nc -vz 127.0.0.1 5060Common problems with port 5060
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5060. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5060' or sudo lsof -i :5060. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5060 at a glance
| Port number | 5060 |
|---|---|
| Service name | sip |
| Transport protocol | TCP / UDP / SCTP |
| Category | Voice and real-time media |
| Range | Registered port (1024–10000) |
| Risk level | Medium |
| Registered assignee | Not listed |
| Reference | [RFC 3263] |
| Registry description | SIP |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5060 used for?
Port 5060 (SIP) uses TCP / UDP / SCTP. SIP.
How do I check if port 5060 is open?
On Linux run `sudo ss -tlpn 'sport = :5060'` and `sudo ss -ulpn 'sport = :5060'` and `sudo ss -Slpn 'sport = :5060'`. On Windows run `Get-NetTCPConnection -LocalPort 5060 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 5060 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5060; empty output usually means nothing is bound to it. UFW and the built-in Windows cmdlets cover TCP and UDP only; SCTP needs nftables, iptables or the vendor's diagnostic tool.
How do I block port 5060?
With UFW run `sudo ufw deny 5060/tcp` and `sudo ufw deny 5060/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5060 -j DROP` and `sudo iptables -A INPUT -p udp --dport 5060 -j DROP` and `sudo iptables -A INPUT -p sctp --dport 5060 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot. UFW covers TCP and UDP only; use iptables or nftables for SCTP.
Is port 5060 safe to expose?
SIP endpoints are scanned for toll fraud and registration hijacking. Require authentication, rate limiting and a trusted SIP trunk. Nevertheless, expose this port only when the service is actually needed. Keep it patched, prefer an encrypted alternative, and limit source addresses with a firewall allowlist.
Related ports
- Port 5054 · rlm-adminRLM administrative interface
- Port 5061 · sipsSIP-TLS
- Port 4804 · aja-ntv4-discAJA ntv4 Video System Discovery
- Port 4621 · ventosoBidirectional single port remote radio VOIP and Control stream
- Port 5209 · nomadNomad Device Video Transfer
- Port 4307 · trueconfTrueConf Videoconference Service
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy