PortAtlas.
Registered port (1024–10000) Standard/Low risk

Port 4402 DS-CLNT

Quick answer

Port 4402 is the IANA-assigned ds-clnt port for ASIGRA Televaulting DS-Client Service (TCP / UDP).

Check and block Is it safe? Troubleshooting FAQ
TransportTCP / UDP
RiskStandard/Low
Typical useInfrastructure and administration

What is port 4402 used for?

Port 4402 is assigned to ds-clnt and uses TCP / UDP. The IANA registry describes the service as “ASIGRA Televaulting DS-Client Service”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.

Ports are the transport-layer address a service listens on. A client that wants to reach ds-clnt connects to port 4402. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.

Use the commands below to confirm whether port 4402 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.

Browse all Infrastructure and administration ports

Source: IANA Service Name and Transport Protocol Port Number Registry.

Check and block port 4402

Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.

Check on Linux

sudo ss -tlpn 'sport = :4402' sudo ss -ulpn 'sport = :4402'

Check on Windows

Get-NetTCPConnection -LocalPort 4402 -State Listen -ErrorAction SilentlyContinue Get-NetUDPEndpoint -LocalPort 4402 -ErrorAction SilentlyContinue

Block with UFW

sudo ufw deny 4402/tcp sudo ufw deny 4402/udp

Block with iptables

sudo iptables -A INPUT -p tcp --dport 4402 -j DROP sudo iptables -A INPUT -p udp --dport 4402 -j DROP

These commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.

Is port 4402 safe to expose?

Standard/Low

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Where port 4402 is usually used

Most traffic on port 4402 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.

Demo

Probe the control-plane service

These services are high-value targets. Verify the listener from a trusted host before changing firewall rules.

nc -vz 127.0.0.1 4402

Common problems with port 4402

Connection refused or timed out

Refused usually means the host is reachable but nothing is listening on port 4402. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.

Port already in use

Find the process holding the port with sudo ss -tlpn 'sport = :4402' or sudo lsof -i :4402. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.

Firewall rule did not survive a reboot

UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.

The port is blocked but still reachable

A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.

Port 4402 at a glance

Port number4402
Service nameds-clnt
Transport protocolTCP / UDP
CategoryInfrastructure and administration
RangeRegistered port (1024–10000)
Risk levelStandard/Low
Registered assigneeNot listed
Registry descriptionASIGRA Televaulting DS-Client Service
SourceIANA Service Name and Transport Protocol Port Number Registry

Frequently asked questions

What is port 4402 used for?

Port 4402 (DS-CLNT) uses TCP / UDP. ASIGRA Televaulting DS-Client Service.

How do I check if port 4402 is open?

On Linux run `sudo ss -tlpn 'sport = :4402'` and `sudo ss -ulpn 'sport = :4402'`. On Windows run `Get-NetTCPConnection -LocalPort 4402 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 4402 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 4402; empty output usually means nothing is bound to it.

How do I block port 4402?

With UFW run `sudo ufw deny 4402/tcp` and `sudo ufw deny 4402/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 4402 -j DROP` and `sudo iptables -A INPUT -p udp --dport 4402 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.

Is port 4402 safe to expose?

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

See all Infrastructure and administration ports

Primary data: IANA Service Name and Transport Protocol Port Number Registry.

Last reviewed 2026-10-30 · Methodology · About · Privacy