Port 36411 WLCP
Port 36411 is the IANA-assigned wlcp port for Wireless LAN Control plane Protocol (WLCP) (UDP).
What is port 36411 used for?
Port 36411 is assigned to wlcp and uses UDP. The IANA registry describes the service as “Wireless LAN Control plane Protocol (WLCP)”. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default.
Ports are the transport-layer address a service listens on. This entry has no TCP assignment: UDP is connectionless, so a client that gets no reply may be hitting either an idle service or a firewall drop. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 36411 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all Infrastructure and administration ports
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [_3GPP].
Check and block port 36411
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -ulpn 'sport = :36411'Check on Windows
Get-NetUDPEndpoint -LocalPort 36411 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 36411/udpBlock with iptables
sudo iptables -A INPUT -p udp --dport 36411 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 36411 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 36411 is usually used
Most traffic on port 36411 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Service discovery, configuration and secret management for other systems.
- Administration panels used by operators rather than end users.
- Automation that reads or updates control-plane state on port 36411.
Confirm the UDP listener
This port is not registered for TCP, so an nc TCP probe cannot confirm it. Run this on the host that runs the service; empty output means nothing is bound to port 36411.
sudo ss -ulpn 'sport = :36411'Common problems with port 36411
No reply from the service
Because UDP has no handshake, a missing reply can mean the service is idle, the packet was dropped, or the client sent it to the wrong interface. Check the listener locally before blaming the network.
Port already in use
Find the process holding the port with sudo ss -ulpn 'sport = :36411' or sudo lsof -i :36411. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 36411 at a glance
| Port number | 36411 |
|---|---|
| Service name | wlcp |
| Transport protocol | UDP |
| Category | Infrastructure and administration |
| Range | High port (10001–65535) |
| Risk level | Standard/Low |
| Registered assignee | [_3GPP] |
| Registry description | Wireless LAN Control plane Protocol (WLCP) |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 36411 used for?
Port 36411 (WLCP) uses UDP. Wireless LAN Control plane Protocol (WLCP).
How do I check if port 36411 is open?
On Linux run `sudo ss -ulpn 'sport = :36411'`. On Windows run `Get-NetUDPEndpoint -LocalPort 36411 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 36411; empty output usually means nothing is bound to it.
How do I block port 36411?
With UFW run `sudo ufw deny 36411/udp`. With iptables run `sudo iptables -A INPUT -p udp --dport 36411 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 36411 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy