PortAtlas.
Registered port (1024–10000) Standard/Low risk

Port 2874 DXMESSAGEBASE1

Quick answer

Port 2874 is the IANA-assigned dxmessagebase1 port for DX Message Base Transport Protocol (TCP / UDP).

Check and block Is it safe? Troubleshooting FAQ
TransportTCP / UDP
RiskStandard/Low
Typical useApplication services

What is port 2874 used for?

Port 2874 is assigned to dxmessagebase1 and uses TCP / UDP. The IANA registry describes the service as “DX Message Base Transport Protocol”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.

Ports are the transport-layer address a service listens on. A client that wants to reach dxmessagebase1 connects to port 2874. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.

Use the commands below to confirm whether port 2874 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.

Source: IANA Service Name and Transport Protocol Port Number Registry.

Check and block port 2874

Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.

Check on Linux

sudo ss -tlpn 'sport = :2874' sudo ss -ulpn 'sport = :2874'

Check on Windows

Get-NetTCPConnection -LocalPort 2874 -State Listen -ErrorAction SilentlyContinue Get-NetUDPEndpoint -LocalPort 2874 -ErrorAction SilentlyContinue

Block with UFW

sudo ufw deny 2874/tcp sudo ufw deny 2874/udp

Block with iptables

sudo iptables -A INPUT -p tcp --dport 2874 -j DROP sudo iptables -A INPUT -p udp --dport 2874 -j DROP

These commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.

Is port 2874 safe to expose?

Standard/Low

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Where port 2874 is usually used

Most traffic on port 2874 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.

Demo

Probe the port

Confirm something is listening before you debug the client. This checks a TCP handshake on the port.

nc -vz 127.0.0.1 2874

Common problems with port 2874

Connection refused or timed out

Refused usually means the host is reachable but nothing is listening on port 2874. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.

Port already in use

Find the process holding the port with sudo ss -tlpn 'sport = :2874' or sudo lsof -i :2874. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.

Firewall rule did not survive a reboot

UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.

The port is blocked but still reachable

A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.

Port 2874 at a glance

Port number2874
Service namedxmessagebase1
Transport protocolTCP / UDP
CategoryApplication services
RangeRegistered port (1024–10000)
Risk levelStandard/Low
Registered assigneeNot listed
Registry descriptionDX Message Base Transport Protocol
SourceIANA Service Name and Transport Protocol Port Number Registry

Frequently asked questions

What is port 2874 used for?

Port 2874 (DXMESSAGEBASE1) uses TCP / UDP. DX Message Base Transport Protocol.

How do I check if port 2874 is open?

On Linux run `sudo ss -tlpn 'sport = :2874'` and `sudo ss -ulpn 'sport = :2874'`. On Windows run `Get-NetTCPConnection -LocalPort 2874 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 2874 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 2874; empty output usually means nothing is bound to it.

How do I block port 2874?

With UFW run `sudo ufw deny 2874/tcp` and `sudo ufw deny 2874/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 2874 -j DROP` and `sudo iptables -A INPUT -p udp --dport 2874 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.

Is port 2874 safe to expose?

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Primary data: IANA Service Name and Transport Protocol Port Number Registry.

Last reviewed 2026-10-30 · Methodology · About · Privacy