Port 27504 KOPEK-HTTPHEAD
Port 27504 is the IANA-assigned kopek-httphead port for Kopek HTTP Head Port (TCP / UDP).
What is port 27504 used for?
Port 27504 is assigned to kopek-httphead and uses TCP / UDP. The IANA registry describes the service as “Kopek HTTP Head Port”. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default.
Ports are the transport-layer address a service listens on. A client that wants to reach kopek-httphead connects to port 27504. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 27504 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Sten_H_Danielsen].
Check and block port 27504
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :27504'
sudo ss -ulpn 'sport = :27504'Check on Windows
Get-NetTCPConnection -LocalPort 27504 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 27504 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 27504/tcp
sudo ufw deny 27504/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 27504 -j DROP
sudo iptables -A INPUT -p udp --dport 27504 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 27504 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 27504 is usually used
Most traffic on port 27504 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Serving a website, API or reverse-proxy traffic that clients reach on port 27504.
- Load-balancer and uptime checks probing the port before routing requests.
- Local development, where a browser or curl calls the service on localhost:27504.
Send a test request
Start a local web server, then ask the port for response headers. Replace 127.0.0.1 with the host you are testing.
curl -I http://127.0.0.1:27504Common problems with port 27504
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 27504. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :27504' or sudo lsof -i :27504. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 27504 at a glance
| Port number | 27504 |
|---|---|
| Service name | kopek-httphead |
| Transport protocol | TCP / UDP |
| Category | Web and HTTP |
| Range | High port (10001–65535) |
| Risk level | Standard/Low |
| Registered assignee | [Sten_H_Danielsen] |
| Registry description | Kopek HTTP Head Port |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 27504 used for?
Port 27504 (KOPEK-HTTPHEAD) uses TCP / UDP. Kopek HTTP Head Port.
How do I check if port 27504 is open?
On Linux run `sudo ss -tlpn 'sport = :27504'` and `sudo ss -ulpn 'sport = :27504'`. On Windows run `Get-NetTCPConnection -LocalPort 27504 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 27504 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 27504; empty output usually means nothing is bound to it.
How do I block port 27504?
With UFW run `sudo ufw deny 27504/tcp` and `sudo ufw deny 27504/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 27504 -j DROP` and `sudo iptables -A INPUT -p udp --dport 27504 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 27504 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 27442 · jesmsjcJob controller service
- Port 27782 · ars-vistaARS VISTA Application
- Port 24680 · tcc-httpTCC User HTTP Service
- Port 44323 · pmwebapiHTTP binding for Performance Co-Pilot client API
- Port 23546 · areaguard-neoAreaGuard Neo - WebServer
- Port 22555 · vocaltec-wconfVocaltec Web Conference
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy