PortAtlas.
High port (10001–65535) Standard/Low risk

Port 13218 EMC-VCAS-UDP

Quick answer

Port 13218 has a different IANA assignment for each transport protocol: TCP emc-vcas-tcp; UDP emc-vcas-udp.

Check and block Is it safe? Troubleshooting FAQ
TransportTCP / UDP
RiskStandard/Low
Typical useCustom high ports

What is port 13218 used for?

Port 13218 carries a different IANA service on each transport protocol: TCP emc-vcas-tcp; UDP emc-vcas-udp. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default. The same port is also registered under emc-vcas-tcp.

Each transport reaches a different service on this number, so match the protocol to the service you are diagnosing. A TCP check says nothing about a UDP listener on the same port, and the reverse is also true. Both transports still bind to the same number, which is why two processes can collide even when they use different protocols.

Use the commands below to confirm whether port 13218 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.

Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Mark_O_Connell].

Check and block port 13218

Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.

Check on Linux

sudo ss -tlpn 'sport = :13218' sudo ss -ulpn 'sport = :13218'

Check on Windows

Get-NetTCPConnection -LocalPort 13218 -State Listen -ErrorAction SilentlyContinue Get-NetUDPEndpoint -LocalPort 13218 -ErrorAction SilentlyContinue

Block with UFW

sudo ufw deny 13218/tcp sudo ufw deny 13218/udp

Block with iptables

sudo iptables -A INPUT -p tcp --dport 13218 -j DROP sudo iptables -A INPUT -p udp --dport 13218 -j DROP

These commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.

Is port 13218 safe to expose?

Standard/Low

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Where port 13218 is usually used

Most traffic on port 13218 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.

Demo

Probe the port

Confirm something is listening before you debug the client. This checks a TCP handshake on the port.

nc -vz 127.0.0.1 13218

Common problems with port 13218

Connection refused or timed out

Refused usually means the host is reachable but nothing is listening on port 13218. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.

Port already in use

Find the process holding the port with sudo ss -tlpn 'sport = :13218' or sudo lsof -i :13218. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.

Firewall rule did not survive a reboot

UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.

The port is blocked but still reachable

A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.

Port 13218 at a glance

Port number13218
Service nameemc-vcas-udp
Aliasesemc-vcas-tcp
Transport protocolTCP / UDP
Assignments by protocol
  • TCP emc-vcas-tcp — EMC Virtual CAS Service
  • UDP emc-vcas-udp — EMV Virtual CAS Service Discovery
CategoryCustom high ports
RangeHigh port (10001–65535)
Risk levelStandard/Low
Registered assignee[Mark_O_Connell]
Registry descriptionEMV Virtual CAS Service Discovery
SourceIANA Service Name and Transport Protocol Port Number Registry

Frequently asked questions

What is port 13218 used for?

Port 13218 (EMC-VCAS-UDP). The IANA registry assigns a different service on each transport protocol: TCP emc-vcas-tcp; UDP emc-vcas-udp.

How do I check if port 13218 is open?

On Linux run `sudo ss -tlpn 'sport = :13218'` and `sudo ss -ulpn 'sport = :13218'`. On Windows run `Get-NetTCPConnection -LocalPort 13218 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 13218 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 13218; empty output usually means nothing is bound to it.

How do I block port 13218?

With UFW run `sudo ufw deny 13218/tcp` and `sudo ufw deny 13218/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 13218 -j DROP` and `sudo iptables -A INPUT -p udp --dport 13218 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.

Is port 13218 safe to expose?

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Primary data: IANA Service Name and Transport Protocol Port Number Registry.

Last reviewed 2026-10-30 · Methodology · About · Privacy